Devices You Need to Set Up a New Bathtub
Devices You Need to Set Up a New Bathtub
Blog Article
In this article in the next paragraph yow will discover a good deal of quality ideas in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a bathtub isn't precisely brain surgery, but it does need solid plumbing, woodworking, and also in some cases, tiling skills. Replacing an old bath tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily available, the task can relocate quickly; if you have to open up a wall to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub as well as embeded in the new one. Ensure you have certified on your own for the job and fit trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is better to think about utilizing one before you begin. Opportunities are you may require a specialist plumber to make tube links.
This article will assist you set up a new tub in your shower room if you have actually currently acquired a brand-new tub and don't need to alter the plan of your previous water system pipelines.
Your devices and also product checklist should comprise the following:
Getting ready for the Installation
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you use every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its last setting.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you should do is separate the supply of water. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to moving on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Installing the Tub
Making use of both wooden boards under its feet, put the bath tub in the required setting. The wood boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bathtub until the level reviews level.
To install taps, fit all-time low of the outermost flexible tap adapter to the ideal supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the supply of water as well as examine all joints and new pipework for leaks as well as tighten them if needed. Load the bathtub and likewise inspect the overflow electrical outlet and also the normal outlet for leaks.
Lastly, take care of the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub should wait until the tub has been utilized a minimum of when as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washing machines remain in place between the faucet as well as the sink. Protect the tap in position with the maker supplied backnut. Once the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind must be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to split a stiff seal, causing the water to pass through the wall surface between the bathroom and also the tiling, resulting in complications with wetness as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill the tub with water before securing, to enable the activity experienced when the tub is in usage. The sealant can split fairly very early if you do not consider this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the marketplace. It is recommended to fit the floor tiles making use of water-resistant or water-proof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading about How to Install a Bathtub? Write a comment below. We'd be glad to find out your thinking about this posting. In hopes that you come back again later on. Please set aside a second to share this entry if you liked it. Thanks a lot for your time. Please come visit our blog back soon.
Book Service Now
Report this page